Menu
Contact Us
banner image

Blogs

Integrated machine shop and fabrication workshop with rows of lathes and machining equipment
October 2nd, 2026

What Are the Advantages of an Integrated Machine Shop and Fabrication Team?

When industrial equipment needs a repair, modification, or replacement component, the work rarely involves just one process. Before a damaged component can be put back into operation, it might require machining, welding, fabrication, dimensional correction, assembly, and testing. An integrated machine shop and fabrication team could have a significant role

Read More
Three-phase electric motor sent for rewinding after repeated failure caused by single phasing
September 16th, 2026

Why Motors Keep Failing After Rewinding: The Hidden Problem of Single Phasing

A motor that keeps failing after rewinding usually has an unresolved supply fault, most often single phasing. One phase is lost, the remaining phases carry excessive current, and the new windings overheat and burn out just as the old ones did. Rewinding repairs the damage, not the cause, so check

Read More
Daniel Group technicians inspecting chilled water pump motors in a building plant room
September 8th, 2026

Common Causes of Chilled Water Pump (CWP) Motor Failures

The most common cause of chilled water pump motor failure is overheating, driven by overloading, blocked ventilation, high ambient temperatures, poor lubrication or frequent starts and stops. Electrical faults, bearing wear, misalignment, pump cavitation and skipped preventive maintenance account for most of the rest, and many show warning signs well

Read More
Damaged electric motor stator core with burnt laminations and deteriorated winding insulation
August 17th, 2026

The Hidden Cost of Ignoring Electric Motor Stator Core Repairs and Testing

Stator core testing belongs in every rewind, because shorted laminations and broken-down interlaminar insulation create hot spots that destroy a new winding. Core loss testing, loop testing or EL CID testing on larger machines finds these faults, and repairing the core first prevents a second rewind for the same failure.

Read More
OTIS permanent magnet synchronous motor for a lift undergoing overhaul and testing at Daniel Group
August 17th, 2026

Why a Permanent Magnet Synchronous Motor Overhaul for Lifts Demands Absolute Precision

A permanent magnet synchronous motor overhaul for a lift demands more precision than an induction motor job, because the rotor carries high-strength magnets and the rotor-to-stator air gap is very small. Mishandled magnets, badly fitted bearings or an unbalanced rotor can cause vibration, demagnetisation, drive faults and, at worst, complete

Read More
Dust-covered industrial electric motor at cement plant ready for overhauling
July 13th, 2026

Why Cement and Crusher Plant Motors Need Regular Overhauling

Cement and crusher plant motors need regular overhauling because dust ingress, shock loading, constant vibration and frequent start-stop cycles wear their bearings, insulation and windings faster than in most industries. A scheduled overhaul finds that hidden deterioration before it becomes a seized bearing or burnt winding that stops a crusher,

Read More
Daniel Group technician performing dynamic balancing of rotating machinery UAE
July 6th, 2026

The Hidden Cost of Skipping Dynamic Balancing on Rotating Machinery

Skipping dynamic balancing after a repair saves the workshop time and labour, but the plant pays for it: residual imbalance drives high vibration, early bearing failure, shaft deflection, rotor cracking, higher energy use and unplanned downtime. The cheapest place to remove imbalance is on a balancing machine in the workshop,

Read More
Cooling tower gearbox motor unit overhauling at Daniel Group UAE
June 9th, 2026

Step-by-Step Guide to Cooling Tower Gearbox Motor Unit Overhauling

A cooling tower gearbox motor unit overhaul follows seven steps: condition assessment, safe dismantling, cleaning and component inspection, repair or replacement, oil change and lubrication, reassembly with precision alignment, and testing before return to service. Done in that order, it catches bearing wear, oil contamination, misalignment and gear damage before

Read More
Generator alternator overhauling specialised facilities
June 4th, 2026

Generator Alternator Overhauling: Why Specialised Facilities Matter

Generator overhauling belongs in a specialised facility because an alternator is several interconnected systems, not one winding. The main stator, rotor, exciter, AVR and rectifier must be diagnosed, repaired and tested together, which takes a test bench, a burn-off oven, varnish immersion, dynamic balancing and cranes that can lift the

Read More